Media Converter 10G-WinTop

Media Converter 10G-WinTop

Media Converter 10G-WinTop

Media Converter 10G-WinTop

Media Converter 10G-WinTop
Media Converter 10G-WinTop
Giỏ hàng (0)
0916946122

Media Converter 10G-WinTop

Mã sản phẩm: 10G-WINTOP

10G Base-T to 10G Base-R Media Converter User’s Manual

Liên hệ
Số lượng:
Hướng dẫn mua hàng
Thông tin chi tiết
Bình luận

1. Overview 

10G Base-T to 10G Base-R Media Converter supports two types media for network connection such as 10GBase-T and 10GBase-FX. The bridge media converter is designed with a 10Gbase Ethernet PHY chip that connects two types segments operation smoothly. This converter can be used as standalone unit or as slide-in module to the 19” converter rack Chassis for use at a central wiring closet. 

2. Technical Specifications

Standards 1000Base-T,  2.5GBase-T, 5Gbase-T, 10Gbase-T
1000Base-X, 2500Base-X,  5GBase-R , 10GBase-R
Media Supported

1000Base-T: Cat5 UTP/STP. MAX 100m;

2.5GBase-T: Cat5e UTP/STP. MAX 50m;

5GBase-T: Cat5e UTP/STP. MAX 50m;

10Base-T: Cat6a UTP/STP. MAX 50m;

Port Type RJ45,  SFP Slot 
Work Mode

1000Base-T  to  1000Base-X
2.5GBase-T  to  2500Base-X

5Gbase-T    to  5GBase-R 

Power Supply 12V DC 
Power 
consumption
MAX 5W
Operation Tempera tore 0 to 55
Relative Humidity 5% to 80% (non-condensation)
3. Installing the Converter
For as a standalone unit: 
→ Verify the DC adapter conforms to your country DC power requirement and insert the power plug 
→ Connect the media cable for network connection
For as a slide-in unit:
→ The slide-in Media Converter and Converter Rack Chassis should supplied only from the same source, both Media Converter Rack Chassis are built to match each other at dimension, DC jack, DC receptacle and power safety. 
→ Turn off the 19” converter rack power 
→ Locate +12V DC power jack on converter back, carefully slide in and plug to 19” rack +12V DC power receptacle 
→ Connect the media cable for network connection 
→ Turn on the converter rack power, the Power LED will light up

Wire connection, Front and Side panel

 4. Check List 

Before you start installing the Converter, verify that the package contains the following: 
---The TP-Fiber Converter 
---AC to 12V DC Power Adapter (for external models) or Power Cord (for internal models) 
---The User’s Manual 
Please notify your local sales distributor immediately if any of the aforementioned items is missing or damage

5. LED Description
LED Status Description
PWR On Power is on and normal.
FX Link/Act On Connection status display for Fiber Link.
ON” indicates that Fiber link is in correct connection.
  Blink Active status display of fiber link.
“Blink” indicates packet goes through FX end.
SD On Fiber signal is detected.
10G On Transfer rate of electric interface is 10Gbps.
  Off Rate of electric interface is 10Mbps.
TX Link On Connection status display for electric link.
“ON” indicates that electric link is in correct
TX Act Blink Active Status display of fiber link
“Blink” indicates packet goes through TX end.
Sản phẩm cùng loại
Close
sản phẩm mới đã được thêm vào giỏ hàng của bạn
Giỏ hàng của tôi
( Sản phẩm)
Tạm tính
Tổng tiền (Tổng số tiền thanh toán):
Hotline tư vấn miễn phí: 0916946122
Top